Reborn in 1982: I Became the Richest Man by Repairing Cars

Chapter 16 Professional Operations: Disassembling the BJ212

The next morning, just as dawn was breaking, the breakfast stalls at the entrance of the alley were just set up, and the aroma of fried dough sticks wafted across half the street.

Jiang Hui and Lin Yuanwu, carrying two steamed buns, ran all the way to the bus stop and squeezed onto the rattling No. 3 bus.

The bus was packed with people, with no room to put their arms or legs. The two of them were squeezed in the middle and swayed for almost an hour before finally arriving at the hardware factory that Chen Qingxiang had mentioned.

Fortunately, Chen Qingxiang had already spoken to the factory yesterday, and the gatekeeper had them fill out some information in the registration book and made a phone call to call for more people.

The two sat on the stone stool by the door for about ten minutes when a middle-aged man in a dark blue Zhongshan suit walked out quickly.

Perhaps because Chen Qingxiang had mentioned Jiang Hui's young age beforehand, Bao Jianshe, the logistics director of the hardware factory, didn't show much surprise when he saw the two of them.

His brows were furrowed tightly, which clearly indicated that he was in a bad mood.

"Master Jiang, right?"

Bao Jianshe, being straightforward, didn't exchange any pleasantries. He pointed into the yard and said, "That's the Beijing 212. I told Old Chen about the problems yesterday, and he should have told you everything, right?"

In the corner of the yard, the military green BJ 212 was covered in a layer of dust, probably because it hadn't been driven for a while.

This was a hot commodity in the 1970s and 80s, the first choice for official vehicles of the military and factories. Eight out of ten Jeeps on the street were this model.

The "BJ212 Light Off-Road Vehicle User and Maintenance Manual" specially compiled by BAIC has become a treasure for drivers and mechanics, with almost everyone having a copy.

But even a manual is just a manual; when faced with real problems, you're still clueless.

The hardware factory's driver tried to fix it himself, and the experienced mechanics they hired from outside also disassembled the engine, but they still couldn't find the root cause of the problem.

Bao Jianshe felt a headache coming on just looking at the car. As the logistics director, he was constantly being urged by the factory manager to get a car, and now he could only pin his last hope on Jiang Hui.

"Yes, Uncle Chen told me about the possible causes of the malfunction, and I've come up with about five or six possibilities in my mind."

Jiang Hui nodded, his tone calm, "We'll check them one by one later, and I guarantee we can fix them."

When dealing with customers who don't like beating around the bush, no amount of polite talk will help; the real test is their skills.

If it's fixed, everything is fine; if it's not fixed, even the warmest small talk is useless.

Bao Jianshe took out his car keys and handed them over, not forgetting to make it clear beforehand: "Here are the car keys. It's Saturday today, so I'll give you a maximum of two days."

"If it can't be fixed in two days, we'll go directly to BAIC and ask the original mechanics for it. Then we won't be able to settle your repair bill."

The original mechanics at BAIC are not the kind of mechanics that small factories like hardware stores can hire.

Otherwise, Bao Jianshe would have gone to invite him long ago.

His words were merely an attempt to put pressure on Jiang Hui and his group.

"Don't worry, Director Bao. I'll get it sorted out by tomorrow morning at the latest, and I'll try to get it done before I leave work today."

Jiang Hui took the keys, immediately rolled up his sleeves, and looked ready to get to work at any moment.

The moment his hand touched the car door handle, the [Auto Repair Encyclopedia System] activated instantly.

The root cause and solution to the problem of this Beijing 212 are as clear as if they were etched in my mind—loose valve seats.

This flaw is well hidden; no wonder the previous masters all stumbled.

Of course, no step of the required procedure can be omitted.

Jiang Hui opened the hood, turned the key, and started the engine. The BJ212's 492 engine sputtered to life.

At idle, a sharp "ticking" sound comes from the cylinder head area, which is much more piercing than ordinary valve noise.

He stepped on the gas, the engine revved up, and the noise increased in frequency, making Bao Jianshe next to him frown.

Jiang Hui squatted down, picked up a long screwdriver that had been polished to a shine, pressed one end tightly against the side of the cylinder head valve chamber, and held the other end to his ear. He slowly moved the screwdriver around, carefully trying to pinpoint the source of the unusual noise.

A moment later, he turned off the engine and said confidently, "The valve seat is loose. Judging from the noise and the power loss, the cylinder head needs to be removed for repair."

This professional operation made Bao Jianshe, who was standing next to him, nod in approval, and most of his doubts disappeared.

"Brother Yuanwu, let's start by preparing to disassemble the machine."

Jiang Hui turned around and called out, deliberately slowing down his movements so that Lin Yuanwu could learn a few tricks.

He first turned on the coolant drain valve and watched as the rusty coolant gushed into the prepared iron bucket.

Next, the carburetor, air filter, and intake and exhaust manifold were removed one by one and carefully placed on the wooden board next to them, for fear of bumping or damaging them.

When removing the cylinder head bolts, Jiang Hui slowed down, explaining to Lin Yuanwu as he tightened them: "The cylinder head of this 492 engine is made of cast iron, so you have to loosen it gradually in three steps, following a diagonal sequence."

"If you use too much force or mess up the order, the cylinder head will deform, and when you put it back, the cylinder head gasket will leak, which will be even more troublesome."

After removing all the bolts, Jiang Hui and Lin Yuanwu together steadily lifted the cylinder head.

Then gently place it on a floor covered with thick wooden planks to prevent the cylinder head from directly contacting oil and gravel.

Next, Jiang Hui disassembled the valve mechanism, took out his self-made valve spring compressor, clipped it onto the valve spring seat, and slowly applied pressure.

After the spring tension was fully released, he carefully removed the locking plate with small tweezers, then loosened the compressor and took out the spring seat, spring and valve in turn.

As he disassembled each valve, he neatly arranged them on the wooden board in cylinder order 1-3-4-2, and even marked the valve stems with chalk: "Remember, valves cannot be mixed up in different cylinders!"

"The wear of valves in each cylinder is different. If you install the wrong valves, the valve clearance will not be adjusted properly, which will aggravate the abnormal noise."

Once the valves were removed, the fault was immediately exposed.

There is a noticeable gap between the edge of the valve seat ring of the third cylinder and the cylinder head seat hole.

Jiang Hui gently pried it with a screwdriver, and the seat ring could actually wobble slightly. There were also a lot of black metal shavings stuck to the edge, which were the impurities that had rubbed off the seat ring and cylinder head.

Meanwhile, Bao Jianshe, who had been impressed by Jiang Hui's professionalism, had already returned to his office. On the contrary, the factory's drivers were curiously watching from a distance.

"See that?"

Jiang Hui wiped the seat hole and seat ring clean with a rag, pointed to the fault and explained to Lin Yuanwu, "The tolerance between this cast iron seat ring and the cylinder head is not very precise to begin with, and the engine is subjected to long-term high and low temperature alternation."

"In addition, this car often runs on dirt roads in the suburbs, and the valve impact is great when climbing hills, so the gaps wear out more and more."

"If the seal is poor, the power will naturally be insufficient, and it may also cause backfire and explosion."

"Next, we need to remove this loose seat ring."

Jiang Hui picked up a soft copper rod. "Use this to pad the inside of the cylinder seat and gently tap from the back of the cylinder head. The force should be even and gentle. Never use a hammer to hit it directly."

"This cylinder head is very fragile; it cracks easily. We don't have any new cylinder heads to replace it here, so we can only repair it by hand."

After a few taps, the cylinder head seat came off securely from the front.

Jiang Hui picked up the seat ring and examined it carefully. He found that the sealing surface was slightly worn and the inner wall of the seat hole was covered with rust and impurities.

These days, car maintenance is very casual.

In addition, the materials and craftsmanship of the parts were not up to par, so the quality naturally could not compare with that of later generations.

Like engines in later generations, they generally only require normal maintenance and will never malfunction throughout their lifespan.

After disassembly, the next step is to repair the seat hole and seat ring.

Jiang Hui asked Lin Yuanwu to hand him a piece of 200-grit sandpaper and a small bottle of machine oil.

Tap the screen to use advanced tools Tip: You can use left and right keyboard keys to browse between chapters.

You'll Also Like