Reborn in 1982: I Became the Richest Man by Repairing Cars
Chapter 84: Meticulous Operations Showcase True Skill
After getting the bearing, the two immediately rushed back to the repair shop.
Luo Xiehao was in a hurry to get somewhere, and the noise from his wheel hubs was unusually noticeable.
Clearly, he was afraid of missing his car tomorrow.
Jiang Hui sat in the passenger seat, occasionally reminding him, "Drive slowly, don't rush."
However, Jiang Hui knew that at this moment, no amount of comforting words could be as convincing as actions.
So as soon as the car came to a complete stop, Jiang Hui immediately got out.
"Master, I've been to several places, but I haven't been able to buy it."
Fan Weimin, who had just returned to the store, quickly stepped forward to explain.
"It's okay, we've already bought it."
"Perfect timing. You and Yuanwu can bring over the jack, socket wrench, and puller, and then find a thick wooden board to put under the car."
"Okay!"
Fan Weimin didn't dare to delay and quickly grabbed the tools.
Place them one by one next to the SH760.
Then they brought over a thick, polished wooden board and squatted down next to the right front wheel, waiting for its turn.
Jiang Hui put on canvas gloves stained with a little oil and started working.
However, no matter how anxious we are, we cannot waste the teaching opportunity.
"Weimin, the first step in removing the wheel hub bearing is to lift the car. This step is crucial. If you don't lift it securely, the car will slide down and cause a major accident."
As he spoke, he bent down and firmly secured the jack under the main beam of the frame on the inside of the right front wheel.
This is the most sturdy part of the SH760 frame.
"The jack must be aligned with the main beam, not with the safety bar or the fender, otherwise it will deform."
"The car owner will cause us trouble, and it's not safe."
As soon as he finished speaking, Jiang Hui turned the jack lever clockwise with even force, observing the car body as he did so.
"Push it up slowly until the right front wheel is completely off the ground, leaving about a fist's width of space. Don't push it up too high, the higher it goes, the less stable it will be."
Although Lin Yuanwu and Fan Weimin already knew how to use the jack.
However, this did not prevent them from continuing to study diligently.
Fan Weimin, in particular, did not learn as quickly as Lin Yuanwu.
Giving a few more words of advice won't hurt.
Once the wheels were completely off the ground, Jiang Hui immediately grabbed a thick wooden board, placed it firmly under the frame, and shook the vehicle vigorously to confirm that it was truly stable.
"Weimin, no matter which car you're ramming, as long as the wheels are off the ground, you must use safety wood."
"These are the rules, and also a way to save your life. From now on, when you're doing your work, don't be lazy."
"Master, I understand!"
Fan Weimin nodded quickly, keeping Jiang Hui's words firmly in mind.
The next step is to remove the tires.
Jiang Hui picked up the Phillips socket wrench, aligned it with the five lug nuts on the tire, and steadily turned it counterclockwise.
"When removing the screws, you should remove them diagonally, not sequentially, otherwise the wheel hub will be subjected to uneven stress and may easily deform."
As he tightened the screws, he explained to Lin Yuanwu and Fan Weimin, "Loosen them first, don't unscrew them completely. Wait until all four screws are loose."
"Twist them off one by one, it's easier that way and less likely to strip the threads."
Fan Weimin watched from the side, occasionally reaching out to hand Jiang Hui a wrench.
After unscrewing the bolts, Jiang Hui reached out, grabbed the edge of the tire, and gently pulled to remove the heavy tire.
Fan Weimin immediately took it and leaned it against the corner of the repair shop.
"The SH760 has 16-inch tires, which are not light. Be careful when unloading them so you don't hurt your feet."
After removing the tire, the brake drum, rim, and half-shaft of the right front wheel were completely exposed.
It was covered with dust, oil, and frozen mud.
Jiang Hui picked up a brush and first cleaned the surface dust and oil stains. Then he pointed to the brake drum and said, "You see, there can't be any oil stains between the brake drum and the brake pads, otherwise the brakes will fail."
"Be careful when you remove the brake drum later. Don't touch the brake pads or break the brake cable."
As he spoke, he found the fixing screws on the brake drum and unscrewed them.
He reached out and grabbed the edge of the brake drum, gently shook it a few times, and removed the brake drum.
"After removing the brake drum, first check the wear condition of the brake pads to see if there is uneven wear or cracks. If the wear is too severe, you should remind the owner to replace it, otherwise the brakes will not be safe."
Jiang Hui carefully inspected the brake pads and, after confirming that the wear was normal, proceeded to the next step.
Although we are only replacing the wheel bearings today, the wheel bearings we use today are not the same as those of later generations.
Disassembly is quite troublesome; you have to remove all the surrounding parts first.
Fortunately, there wasn't much to dismantle in the surrounding area, and soon it was time to remove the old bearings.
This is also the most strenuous step.
Jiang Hui picked up the puller and firmly gripped the puller's claws onto the outer ring of the bearing inside the wheel hub, ensuring that it was locked in place and aligned correctly.
"The puller must be properly engaged, otherwise it will easily slip when pulling, making it impossible to remove the bearing and potentially damaging the wheel hub."
While adjusting the position of the puller, he instructed, "The hub bearing of the SH760 is a double-row tapered roller bearing, which is highly precise. When disassembling, you must apply even force."
"You can't use brute force to smash it, otherwise the bearing housing will deform, and the new bearing won't last long."
After adjusting the puller, Jiang Hui turned the lever of the puller clockwise, gradually increasing the force.
With a soft "creaking" sound, the old bearing was slowly pulled out of the wheel hub.
"Look at this old bearing. The balls are worn down and pitted, the raceways are scratched, and the grease has burned off and frozen solid."
"That's why it makes noise and goes astray."
Jiang Hui placed the old bearing on the ground and pointed to the balls and raceways inside for everyone to see.
"You see, once this kind of bearing is worn out, it can't be repaired; you have to replace it with a brand new one."
"If you see this situation in the future, just tell the car owner to replace the part; don't waste time trying to repair it."
Luo Xiehao watched this scene from a distance, feeling much more at ease.
Then Jiang Hui picked up a rag, dipped it in kerosene, and carefully cleaned the old grease, rust, and impurities from the wheel hub.
"The wheel hubs must be thoroughly cleaned, especially the inner ring of the bearing housing, which must be free of rust and impurities."
"Otherwise, the new bearing will wear out and we'll have to replace it again soon."
In later years, Jiang Hui rarely repaired wheel bearings.
Most car manufacturers' wheel bearings are maintenance-free for their entire lifespan.
If we occasionally encounter a broken one, we just replace it directly.
At that time, wheel hub bearings had evolved to the third generation, making replacement convenient and simple.
Jiang Hui cleaned it with extra care, even wiping the gaps in the bearing housings until they were spotless.
Then wipe it dry with a dry cloth to make sure there is no oil or moisture left.
"In winter, it's cold, and rust stains are not easy to clean. If you really can't wipe them off, just gently sand them with sandpaper."
"But you can't grind it too hard, otherwise it will widen the clearance of the bearing housing and affect the installation accuracy."
After cleaning, Jiang Hui took out a new wheel hub bearing and prepared to install it.
Jiang Hui carefully aligned the new bearing with the bearing housing on the wheel hub and gently pressed it down with his hand.
First, press the bearing in partially to ensure it is aligned and not misaligned.
"When installing a new bearing, make sure it is aligned correctly and not tilted, otherwise the bearing will be damaged when it is pressed down, and the bearing housing will also be damaged."
Then, he picked up a special sleeve and gently slipped it onto the outer ring of the bearing.
You'll Also Like
-
I'm just an ordinary person passing by.
Chapter 347 2 hours ago -
I, a ship girl, am the savior of civilization.
Chapter 110 2 hours ago -
I am the leader of the anti-racism movement.
Chapter 312 2 hours ago -
My girlfriend isn't as cute as me.
Chapter 588 2 hours ago -
The Daily Life of a Hogwarts Terrorist
Chapter 171 2 hours ago -
Brass Dragons in the Dragon World
Chapter 330 2 hours ago -
Who made him Ultraman!.
Chapter 164 2 hours ago -
Sharing the Heavens Starting from Douluo Continent
Chapter 457 2 hours ago -
Douluo Continent: Transmigrating into Huo Yuhao's world, I start by becoming Yao Lao's app
Chapter 559 2 hours ago -
Douluo Continent: The God of Thunder Descends, Martial Soul Lei Yi
Chapter 91 2 hours ago