I manufacture weapons in the Middle East and am wanted globally?

Chapter 89 "Can an Industrial Giant Still Be Called One Without Sanctions?!"

Chapter 89 "Can an Industrial Giant Still Be Called One Without Sanctions?!"

After Hernandez left, Boss Chen felt a strong urge to try it himself.

Of course he wants to make "mosquitoes" into a series!

He wants to be number one in the future of the military drone industry!

This is a blue ocean~

But you should ask a professional for specific advice on how to do it.

Chen Zheng turned around, bent down, and crawled into the cave.

More than 20 monster laborers were busy at their respective workstations, with wrenches and screwdrivers stuck in the pockets of their work clothes.

"Four-Eyes! Frog! Dog Egg!" Chen Zheng shouted, his voice echoing in the cave, drowning out the roar of the machines.

The three craftsmen turned around at the same time.

"Come over for a meeting!!"

Four-Eyes pushed up his glasses, stood up from in front of the furnace, dusted off his knees, and jogged over. Frog and Dog Egg followed behind. The three craftsmen stood in a row, their six amber eyes all staring at him.

"Boss!" they all called out in unison.

"I have an idea, can you help me see if it's feasible?"

Chen Zheng sorted out the still-forming thoughts in his mind.

"I want to increase the payload capacity of my drone, at least 500 grams, ideally up to one kilogram. Is there any way to do that?"

The three craftsmen exchanged a glance.

Four-Eyes pushed up his glasses. "Boss, increasing the load capacity isn't as simple as replacing the motor with a bigger one or installing a larger battery. It's a systemic project; changing one part affects the whole."

"The payload has been increased from 200 grams to 500 grams, an increase of 300 grams. This 300 grams is not just added to the warhead; it will affect the design parameters of the entire aircraft, starting with the power system. Increased payload means greater lift is needed, greater lift requires larger motors and larger rotor blades, and larger motors mean greater current—"

Chen Zheng frowned upon hearing this.

What the hell are you talking about? I can't understand a word of it, it's like gibberish.

It felt like he was back in school, with the teacher lecturing while he watched porn.

Four-Eyes continued, "Based on current power system efficiency estimates, with a 500-gram payload, the overall takeoff weight will increase from the current 550..."

克左右上升到大约1300克,电机要从2212升级到2814级别,KV值从1000降到800左右,配合11寸或12寸的桨叶,单个电机拉力从800克提升到1800克以上,四个电机总拉力超过7公

The thrust-to-weight ratio is above 5, which provides sufficient redundancy.

「电池要从3S1300毫安时升级到4S 5000毫安时,重量从100克增加到400克左右,续航时间会从现在的12到15分钟下降到8到10分钟,因为更大的桨叶和更重的机身带来的阻力增量超过了电池容量的增幅。」

"The flight controller needs to be replaced. The processing power and sensor accuracy of the KK5.5 are not enough. It needs to be replaced with a new board with a 6-axis gyroscope and electronic image stabilization. The computing frequency needs to be increased at least four times. Otherwise, the 500-gram payload will not be able to maintain its attitude in wind shear environment."

"KT boards can no longer be used for racks."

Tianji chimed in, "The specific strength and specific stiffness of KT board are no longer sufficient for a 500-gram load. During high-G maneuvers, the fuselage will twist and deform, and the deviation between the attitude angle calculated by the flight control and the actual attitude angle will exceed the stability margin. It needs to be replaced with engineering plastic injection molding, or a carbon fiber frame with skin structure. Carbon fiber has better performance but the price is several times higher."

Gou Dan added from the side, "There's another problem. With the addition of image transmission and GPS, the electromagnetic environment of the whole device becomes more complex. The interference between the high-current power lines and signal lines will be more severe. The existing 5.8G image transmission module on a 500-gram mounting platform will have its effective transmission distance reduced from 1.5 kilometers to about 800 meters."

"The GPS module needs to be a version with a shield, and the antenna gain needs to be increased to more than 5dBi, otherwise it is easy to lose signals in urban canyons or environments with strong electromagnetic interference."

"Then the cost per unit is approximately $800."

Chen Zheng's eyes widened suddenly, his mouth opened, and he uttered a muffled "Huh?"

I didn't understand anything else, but I understood this!

Does this mean costs have gone up?!

Four-Eyes said, "Boss, the $800 I mentioned is the B0M cost, not including assembly labor, testing losses, after-sales maintenance, and long-distance shipping. It'll add up to over $1000!"

This cost—how much does it have to sell for?

$5000?

$8000?

If the price is too high, customer loyalty will decrease, because not every customer can afford this kind of product!

It's like no matter how good my novel is, if I don't update it often, people will still criticize me!

"Boss, there's actually one more urgent matter: production capacity has reached its limit," Tianji said, raising his hand.

"Right now, everyone is working at full capacity, non-stop, with no spare capacity."

"Our equipment is also operating at full capacity, 24 hours a day. The utilization rate of each machine tool has exceeded 98%. If it goes any higher, there will be no time for preventive maintenance. If any machine breaks down, the entire production line will have to stop."

After thinking for a moment, Chen Zheng said directly, "From now on, you won't need to do the KT board gluing and simple assembly work."

"I'll find someone to do it; you just do the core processes."

Four-Eyes frowned slightly. "The boss means—outsourcing?"

In the end, we still had to take this step.

Chen Zheng nodded. "You should use the knife to cut meat, not to scrape away hair!"

Four-eyed: ? ? ?

frog:???

Dog Egg (cross-eyed): ? ? ?

Chen Zheng stood up, dusted off his pants, and waved to the four-eyed men, "Alright, alright, you guys go ahead and get busy."

Chen Zheng walked to the innermost corner of the cave, a relatively quiet place, far from the machine tools and generator, where the noise was much less. He squatted down on the ground, leaning against the cool rock wall, and took out his phone from his pocket.

The coolness of the rock wall seeped through his jacket onto his back, giving him a slight respite from the burning desire for cost that had been igniting his mind.

He took a deep breath and opened the Monster Factory app.

Against the dark background, the green fanged monster remained unchanged, its bulging eyes staring ahead, its fangs protruding from its lower lip as if mocking its earlier embarrassment at being frightened by the cost.

[System Prompt:]

Current regional influence: 2047/10000

Factory Level: Lv.3

Next level upgrade requirement: Regional influence reaches 10000

(Note: Current regional influence growth primarily stems from product distribution and combat results in Syria, Lebanon, and Libya. The Assef Shaukat assassination event increased influence by 450, and the NATO forward operating base attack in Libya increased influence by 1200. Please maintain this level of influence.)

Chen Zheng stared at the number "10000" for two seconds, and his lips twitched.

Ten thousand?

He'd worked himself to the bone for so long, blowing up a lieutenant general and several French fighter planes, and only managed to save a little over two thousand. How many things would he have to blow up to reach ten thousand?

Assef Shokat is that cheap?!

He shook his head and swiped his finger down the screen.

[Global Industrial Ranking Climbing Program]

Current ranking: 22997 (Congratulations! You have surpassed 853 competitors!)

Next goal: Within the top 22000 (needs to surpass 997 places)

Award: F-16E parts drawing package (choose one from landing gear door hydraulic actuator, leading edge flap cable tie, and speed brake honeycomb structure).

Note: Can't make complete machines or even parts? Let's start by practicing as an outsourcing contractor!

Chen Zheng's gaze lingered on the line of small red text: "F-16E Parts Blueprint Package".

阿联空军特供版,基于F—16C/D BIock 50/52深度定製,加装了APG—80有源相控阵雷达、保形油箱、全数字电传飞控、改进型F110—GE—132发动机,号称「沙漠隼」。

It first flew in 2003 and was delivered in 2004. The unit price exceeded US$8000 million, which is more expensive than many fourth-generation fighter jets.

Even a small piece of the blueprints for these aircraft parts is far more valuable than any civilian model aircraft.

He squinted and tapped the first option with his finger.

[Landing gear door hydraulic actuator]

(This is a photo of maintenance work on the main landing gear bay of an F-16C. The silver cylinder is the hydraulic actuator, which is hinged at both ends to the door and the fuselage structure. It is exactly the same on the F-16E.)

Main performance:

This thing is the "electric door hinge" of the aircraft landing gear bay door. To lower the landing gear, it has to push the door open; to retract the landing gear, it has to pull the door back and close it.

Sounds simple? Well, the difficulty lies in the fact that you have to push and close a metal hatch weighing several hundred kilograms smoothly and tightly at an altitude of tens of thousands of feet, in an environment of minus forty or fifty degrees Celsius, under the impact of high-speed airflow, without leaking air, getting stuck, shaking, or suddenly becoming unable to open during a landing.

The F-16E's actuator is controlled by an electro-hydraulic servo closed loop, and the position sensor has an accuracy of one-twentieth the diameter of a human hair. The reaction time from fully open to fully closed is less than half a second.

Global manufacturers:

Rockwell Collins (USA): Original equipment manufacturer (OEM) supplier, they do things blindly.

Moog (USA): A global leader in servo valves and actuators, supplying Boeing, Airbus, and Lockheed Martin.

Parker Hanniffen (USA): Again, it's American.

Liebherr (Germany/Switzerland): A prominent company in Europe.

Kawasaki Heavy Industries should be able to do it too!

domestic?

Theoretically, the XX Institute under AVIC can do it. They could figure out the schematics, material formulas, and heat treatment processes by working on them behind closed doors for a few years.

But the question is, have you ever seen any company make third-party compatible parts for the F-16E?

The US aviation standard MIL-SPEC requires certification documents that could fill an entire shipping container. You spend three years developing the product, and then another five years getting airworthiness certification? By then, it's too late.

This thing is high-end, really high-end, but for an arms dealer to make an aircraft cabin door actuator, isn't that a bit off track?

PASS!

He slid his finger to the second option.

【Front Edge Flange Wire Joint】

Main performance:

The leading edge of an airplane wing has a small flap that can be flipped up and down; this is called a leading edge flap.

During takeoff and landing, it extends to increase lift and make the plane fly more stably. This thing is the "screw" that controls the extension and retraction of the flap.

The key lies in precision. The lead accuracy of the lead screw must reach the micrometer level, the thread profile error must be finer than a hair, the transmission efficiency must be high, the backlash must be small, and it must remain unworn for decades under the vibration of the engine and the impact of airflow.

The F-16E uses a ball screw assembly with a reverser and internal circulation. Dozens of small steel balls roll around in the track inside the nut. The diameter tolerance of the steel balls is controlled within 0.001 mm. The material used is carburized bearing steel, with a surface hardness of HRC60 or higher and a core hardness of around HRC35, achieving a balance between rigidity and flexibility.

THK (Japan): The inventor of the ball screw, and the world's leading manufacturer.

NSK (Japan): It's the Japanese again.

HIWIN (Taiwan Province): The technology originates from Japan, the quality is good, and the price is much cheaper.

Schaeffler (Germany): European representative.

Rockwell Collins and Moog also do this, but they only make it for their own systems and don't sell it to others.

Domestically? Yes, there are companies like Laizhou, Hanjiang, Bote, and Nan Gongyi. They've already mastered the low-to-mid-range ball screw market and are doing a lot of work.

Monster Factory can handle precision transmission work, but they roll thousands of units every month?

Forget it, I'll let Baldy and his crew make a few more KT board airplanes first.

The third option:

【Speed ​​Bracket Honeycomb Structure】

Main performance:

The large speed brake on the back of the F-16E deploys during landing to increase aerodynamic drag and help the aircraft slow down.

The main structure of this thing is a honeycomb core material, with hexagonal lattice, like a honeycomb. It is bonded with carbon fiber prepreg skin on the top and bottom to make a sandwich structure. Its specific strength and specific stiffness are ridiculously high, its weight is extremely light, and its impact resistance is also very good.

The problem is that the manufacturing process of this thing is extremely abnormal.

The honeycomb core material must be made of aramid paper or aluminum alloy foil, and go through a series of processes such as coating, lamination, hot pressing, stretching, shaping and curing. The process parameters of each process, such as temperature, pressure, time and adhesive viscosity, must be controlled within an extremely narrow window. If the deviation is even slightly, the honeycomb will collapse or become brittle.

The F-16E's speed brake uses aramid paper honeycomb material, which can withstand temperatures above 200 degrees Celsius, has a compressive strength of over 2 MPa, and a density controlled at around 30 kg/m³. The surface skin uses Hercules carbon fiber prepreg, which is autoclaved and has a rough surface.

To achieve a micrometer density of less than 0.1 micrometers, a series of airworthiness tests, including lightning strikes, bird strikes, vibration, and damp heat cycling, must be passed.

HeceI (USA): The world's leading manufacturer of cellular core materials and the original equipment manufacturer (OEM) supplier for the F-16E.

Cytec (USA, now part of Solvay): Again, it's American.

Euro-Composites, a European supplier of specialty cellular core materials, also supplies Airbus and Dassault.

Showa Aircraft Industry of Japan supplied components to Mitsubishi Heavy Industries.

Domestically, only composite materials companies under AVIC can produce it. They already have aramid paper honeycomb production lines, which are used in domestically produced military and civilian aircraft.

Aerospace composite materials are a major trend, offering lightweight and high-strength properties that can be used in virtually any application, from drones to armored vehicles, from missile casings to soldier helmets.

If we can master this, Monster Factory's composite materials processing capabilities could leap forward significantly.

The problem is that the equipment required for this is incredibly expensive. Autoclaves, automatic feeders, five-axis water jets, non-destructive testing equipment—which one of them doesn't cost a fortune?

Chen Zheng put a cigarette in his mouth, squinted at his phone screen, and swiped back and forth three times.

The threshold for the landing gear door hydraulic actuator is too high, and it doesn't fit with our current business.

His current clients are Syrian rebels, Libyan government forces, and tribal militias in the Bekaa Valley—groups that are even involved in combat.

If there's no aircraft, why would you need landing gear and cabin door actuators?

Even masturbating doesn't make sense—

Precision transmission of the leading-edge flap screw pair is a core competency, but the ball screw level of the F-16E is several orders of magnitude lower than that of the AKM bolt carrier, APS firing pin, and so on.

The honeycomb structure component for the speed brake is quite interesting.

Materials science is not just about machining.

If the Mosquito series drones could use a composite material body, the same payload could have a significantly increased range, and the same range could have a significantly increased payload.

Moreover, this thing can be used on armored vehicles, bulletproof plates, and even individual helmets, and its market potential is much greater than that of wire mesh.

the most important is--

These four-eyed monster craftsmen can deduce the "materials and processes" from the finished product!

Isn't this just open-sourcing a bug?

Holy crap!

Chen Zheng hesitated for a fraction of a second before tapping the third option.

[Option: Speed ​​reduction plate honeycomb structure]

A loading circle popped up on the screen and spun for two seconds.

[Selection successful!]

[The F-16E speed brake honeycomb structure component drawing package has been unlocked!]

[Note: The drawings contain a total of 237 documents, including the production process of aramid paper honeycomb core material, carbon fiber prepreg skin layup design, autoclave curing process parameters, non-destructive testing standards, and a list of airworthiness verification documents. These documents have been stored in the system database and can be accessed at any time.]

[WARNING: This technology is regulated under the U.S. International Trade in Arms Regulations (ITAR). Unauthorized proliferation will face severe sanctions. This system assumes no responsibility for the consequences of user use; the risk of being bombed is increased!!!]

Chen Zheng stared at the red warning sign for two seconds, then chuckled.

"ITAR? Sanctions?"

"If they don't get sanctioned, can they even call themselves industrial giants?!"

>

Tap the screen to use advanced tools Tip: You can use left and right keyboard keys to browse between chapters.

You'll Also Like