Chapter 129
Lin Yuan used 1085 high-carbon steel for the blade of the sewing needle.
The square steel was prepared in advance, and it still had traces of anti-rust oil on it when it was pulled out of the material rack.
He wiped the surface with a cotton cloth several times to clean off the oil stains, and then used calipers to measure the length and cross-sectional dimensions. The cross-section was a standard square, with a side length just enough to forge a blade less than an inch wide after twisting.
He took the old forging hammer from the tool rack and weighed it in his hand.
The wood grain on the hammer handle had been worn smooth and shiny by sweat, and the emblem on the head of the fire dragon gleamed with a dull light in the morning light.
Orange-red flames pierced through the gaps in the charcoal, illuminating the entire furnace. Lin Yuan squatted in front of the furnace door, watching the color changes on the steel surface through the observation hole.
He knew the forging window of 1085 very well, but this time he didn't want ordinary forging; he wanted the internal structure of the steel to be prepared during the heating process—the crystals had to reach the most uniform distribution before twisting.
He used pliers to take the square steel out; its color had reached a bright orange-yellow hue.
The first step is not to twist, but to slightly round the four corners of the square steel to remove stress concentration points on the edges.
The hammer doesn't strike hard, but each blow hits the edge precisely, shaping the square cross-section into a rough, nearly octagonal shape.
After rounding the steel, he sent the square steel back into the furnace to be heated.
This time, the heat had to penetrate evenly from the surface to the core to ensure thorough heating. He waited in front of the furnace for quite a while, turning the steel several times to make sure each side of the square steel was heated evenly.
He waited until the entire square steel bar was completely uniform in color and the surface began to show a slight bright yellow tinge before using pliers to take it out.
He had prepared in advance for the turnaround.
The vise next to the anvil had already been fixed to the ground, with a copper-plated clamp gripping it. Lin Yuan inserted one end of the square steel into the vise's clamp, tightened the handle, and secured the steel firmly. The other end of the square steel was exposed, its length just enough for both hands to operate.
He took a large wrench from the tool rack, slipped the wrench's opening onto the end of the square steel, and gripped it tightly.
Then he took a deep breath and started to twist.
The wrench slowly turned in his hand, the square steel making a faint metallic friction sound as it twisted, like some energy that had been suppressed for too long finally finding a way to be released.
He stared at the surface of the square steel, watching the metal fibers, softened by the high temperature, being twisted into a spiral shape. The twisting speed couldn't be too fast—too fast and the steel would tear; a slower pace would allow the fibers to rearrange themselves in the direction of the twist.
One lap. Two laps. Three laps.
He stopped, loosened the wrench, and stepped back to examine the surface of the square steel. The twisted marks extended evenly from one end to the other, and the density of the spirals appeared visually consistent, with no sections that were too tight or too loose.
Once the temperature dropped to a level where he could touch it, he ran his finger along the surface of the square steel. It felt smooth and had no cracks.
The square steel was returned to the furnace. After being heated to the forging temperature, it was taken out and placed on the anvil to begin forging.
This is the most crucial step in twisting Damascus steel. After twisting, the internal fibrous structure of the steel has formed a spiral arrangement, but the surface remains in its original twisted and uneven state.
The forging process involves flattening the kinked surface to expose the spiral fiber structure, creating a spiral pattern.
However, the forging force must be precisely controlled. If the force is too great, the spiral pattern will be deformed, and the clarity of the pattern will decrease; if the force is too small, the unevenness of the surface will not be flattened, and the pattern will be covered by the residue of oxide scale after pickling.
He began by gently tapping one end of the square steel with the flat surface of a forging hammer. The taps were dense and even, with each strike controlled to be lighter than usual forging. After one round of tapping, he flipped the square steel over and tapped it again. He flipped it over again, rotating all four sides in turn.
As the square steel was hammered, it slowly stretched, transforming from a square cross-section into a flat strip, with its width gradually expanding from just over an inch to nearly two inches.
Spiral patterns began to emerge from the surface—not the flowing, irregular curls of cloud patterns, but rather regular...
The spiraling lines, like a spiral thread, rise from the base of the sword towards the tip.
After forging was complete, he measured the width of the blade with calipers—less than an inch, which matched the dimensions in the document Shen Wei had sent. The thickness narrowed evenly from the hilt towards the tip, reaching a maximum thickness of about a quarter inch and thinning to less than a tenth of an inch at the tip. (One inch = 2.54 centimeters)
He clamped the sword blank in front of the belt sander and began rough grinding.
Start with a coarse grit to remove the surface oxide scale and forging marks, exposing the clean metal layer underneath. After coarse grinding, switch to a finer grit, progressing from 400 grit upwards, grinding each grit until the surface has a uniform silky finish before moving on to the next grit.
After the rough grinding was completed, he immersed the sword blank in the pickling tank.
The pickling solution was a diluted ferric chloride solution, prepared at a slightly lower concentration than usual. The contrast of the Damascus steel's texture is mainly achieved through the difference in corrosion rates between the dark and light steel layers. If the pickling time is too short, the texture won't emerge; if it's too long, the darker layers will be over-corroded, blurring the texture. He mentally timed it, and when the time was almost up, he used an iron hook to scoop the sword blank out of the trough, rinsed it with clean water, neutralized it with baking soda water, and dried it with a cotton cloth.
The sword blade was fully revealed under the light.
The spiral pattern begins near the hilt of the sword, spiraling upwards in concentric circles until it gradually narrows near the tip. The spacing between the lines is uniform, and the spiral direction is consistent. After acid washing, the dark and light layers create a clear black-and-white contrast.
It's not the flowing, cloud-like pattern of cloud motifs, but rather a more regular, mechanical sense of order, like threads machined on the most precise lathe. Yet, upon closer inspection, subtle differences left by hand forging can be seen, giving the entire sword a handcrafted warmth within its neatness.
Lin Yuan held up the sword blank and slowly rotated it in the light. The spiral pattern appeared to rotate as the angle of the light changed, climbing upwards in circles from the base to the tip of the sword.
He put down the sword blank, walked to the office area, took out his laptop from the drawer, and opened the tool modeling file that Xiao Li had sent him.
The design of the sewing needle is simple. The cross-shaped pommel guard has clean lines, with the curves on both sides slightly narrowing, consistent with its appearance in the series. The hilt is fitted with a separate design, with several metal rings fitting onto the leather-wrapped grip, serving both a fixing and decorative purpose.
You'll Also Like
-
Colonia Storm Tour
Chapter 594 19 minute ago -
My two-dimensional resident
Chapter 233 19 minute ago -
Elf: I have a secret realm of emerald green.
Chapter 346 19 minute ago -
Lord of Cinder in American Comics
Chapter 338 19 minute ago -
Let the Bizarre Adventure of the Joestars begin.
Chapter 281 19 minute ago -
Goddess Kaleidoscope
Chapter 314 19 minute ago -
Douluo: My Clone Simulates the Star God.
Chapter 362 19 minute ago -
Days at Hogwarts.
Chapter 814 19 minute ago -
Douluo Continent: A new system every month, starting by tricking Tang San.
Chapter 298 19 minute ago -
Douluo Continent: The Peerless Tang Sect - Sharingan Intercepts Tianmeng
Chapter 325 19 minute ago