The car giant started by marrying the daughter of the king

Chapter 95 Opinions of the Leading Group on Introducing New Technologies
The "Third Automobile Preparatory Group" wanted to buy GM's technology, but GM wanted to form a joint venture.

There is a big gap between the two sides' ideas, and this week's negotiations are destined to be fruitless.

However, the Ministry of First Machine Building also wrote a special report and submitted it to the "Leading Group for Introducing New Technologies" under the State Council for review.

The level of this leading group is relatively high, so all major domestic technology introduction projects need to be reported to them specifically.

A large project like "Sanqi" is naturally no problem.

After reading the report, the elder in charge of this technical team thought that this matter was very important, so he signed his opinion and asked higher-level leaders to approve it.

Finally, the chief engineer personally reviewed it and said, "The joint venture can be done," and then instructed, "Sedans can be jointly produced."

Even though there is this approval, the people below have no idea how to implement it.

It was impossible for people from General Motors to stay in China for such a long time, and ultimately the negotiations ended in failure.

Of course, for both parties, this negotiation was not without gain.

General Motors obtained the exterior design drawings of the new model from Jiang Hui, and China understood that it could engage in joint ventures in the future. This subsequent incident directly affected the negotiations with Shouqi Jeep.

Even the formation of joint ventures in China's automobile industry in the future will be related to the review work promoted by the "Leading Group for Introducing New Technologies" this time.

But these are all things for later.

As for Jiang Hui, at this time he was explaining the cause and effect of the matter to Zhu Jiansheng.

"I was just on a business trip to FAW, but I didn't expect so many things to happen."

"But selling the exterior pictures of a new model for $10 is still too sensitive. You still have to be a little careful."

Zhu Jiansheng was demoted and suffered a lot in the past.

Now, of course, he is afraid that Jiang Hui will fall into a trap.

"Dad, don't worry, I know what's going on."

"By the way, the first phase of the design work for the new BJ212 has basically come to an end. The next phase is to have the various supporting factories start making samples."

“I think this is also a good learning opportunity for our school’s Department of Vehicle Engineering.”

“It is inevitable that there will be some unreasonable aspects in the parts designed on paper.”

“For example, the precision in some places does not need to be designed to be that high, and the tolerance setting in some places is unreasonable.”

“These details are easily overlooked during design, but are easily exposed during production.”

“I think if we can get all the teachers and students in the department involved in this project, there might be unexpected gains.”

Jiang Hui quickly shifted the topic to the new BJ212, which is the bond of cooperation between Capital Institute of Technology and Capital Automobile Manufacturing Plant in recent times.

At the same time, this project is also a good opportunity to demonstrate and enhance the strength of the Vehicle Engineering Department of Capital Institute of Technology.

Jiang Hui plans to push for his father-in-law's promotion step by step in the future, so some opportunities naturally cannot be missed.

If the strength and influence of the school's Vehicle Engineering Department can continue to expand under Zhu Jiansheng's leadership, then his influence in the school will also continue to increase.

It is not impossible to become a principal in the future, and even transferring from a school to a ministry is a very normal operation.

My mother-in-law's family is actually in the system, and my father-in-law is also a person with some background.

If you give it a push, anything is possible.

In China, if you want to build your own automobile factory in the 1980s and 1990s, you definitely can't do it without support. In fact, no matter what era it is, the relationships behind a large automobile factory are relatively complicated.

"We are already cooperating with the Capital Gear Factory, Capital Internal Combustion Engine Factory, Capital Automobile Accessories Factory and other manufacturers. I will also communicate with them in the next few days."

“It’s a good opportunity to combine our theory with their practice.”

Zhu Jiansheng naturally realized the benefits behind Jiang Hui's proposal and was prepared to actively promote it.

"Didn't everyone discuss 'Practice is the only criterion for testing truth' some time ago?"

"I think you can elevate the significance of this action a little bit, and even try to get some newspapers to report it."

Jiang Hui patiently encouraged Zhu Jiansheng to not just bury his head in work, but to look up and see the direction of progress.

Otherwise, even if you work very hard and make great contributions, you often don't get promoted.

In the workplace, especially in state-owned enterprises, this point needs special attention.

"Okay, I'll take care of this."

"Come home for dinner on the weekends when you are free."

Zhu Jiansheng was not stupid, so he naturally felt the "educational" meaning of his son-in-law's words, and felt a little embarrassed.

Fortunately, he also knew that what Jiang Hui said made sense, so he would definitely make the necessary efforts.

After dealing with his father-in-law, Jiang Hui went back to the office to review the drawings of various parts of the new BJ212.

For the automotive industry, it is a critical node to take the drawings and formally find supporting manufacturers to make molds and produce parts.

The OEMs are required to issue formal written instructions to specify which version of the drawings to use to guide production.

If there is an error in the drawing, or the wrong drawing is used, it is likely to cause the mold to be scrapped.

What will be wasted then is not only the money spent on producing the molds, but it may also affect the overall schedule of vehicle development.

Logically speaking, the responsibility for this review should ultimately be shouldered by Chen Qi, but everyone knows what the design of the new BJ212 is.

All drawings will have a step of Jiang Hui's signature confirmation before Chen Qi and Lu Jianqiang sign them.

This was also a novel thing for the technical staff of the supporting factories in the capital.

Everyone has a new understanding of Jiang Hui's position within the Capital Automobile Manufacturing Plant.

Invisibly, Jiang Hui's reputation in the capital's automobile industry has also been further enhanced.

People who work in technology admire most those whose technical capabilities are much stronger than their own.

"Master, Director Zheng called and asked you to go to his office."

Just as Jiang Hui was taking a sip of water from his enamel cup and preparing to take a break, Chen Chenxing received a call and came over to tell Jiang Hui that the factory director was looking for him.

This made Jiang Hui feel a little strange.

Generally speaking, the leader in the factory is only the chief engineer Chen Qi who would come to me directly, while the factory director Zheng Haiming rarely asks me to go to his office directly.

Could it be that something has gone wrong with the cooperation with General Motors again?

With a hint of doubt, Jiang Hui walked towards the factory director's office with a notebook in hand and a pen in the upper left pocket of his work clothes.

(End of this chapter)