Reborn in 1982: I Became the Richest Man by Repairing Cars

Chapter 95 Newcomers, New Apprentices, New Business: Yuanwu's Solo Cultivation Demonstrates Str

Lin Yuanwu seemed very skilled throughout, so Jiang Hui naturally didn't say anything.

Jiang Hui would only point out any faults he hadn't discovered.

"See this? It's this triangular needle valve."

"Over time, the sealing surface became rough, and there was some oil and limescale on it, so it couldn't keep out the oil."

"The oil kept overflowing into the carburetor, leaving oil stains on the ground when the car was parked. The car was also consuming more fuel and had an unstable idle speed."

"Remember, to determine if a needle valve is faulty, besides checking for oil leaks, you can also gently press the float."

"If the needle valve rebounds easily without any jamming, it means the seal is working properly."

"If you can't press it down, or if it doesn't bounce back strongly, it's most likely that the needle valve is clogged or worn out."

In the era of carburetor engines, 60% of engine failures were due to problems with the carburetor, a core component.

Especially in China, the manufacturing process of carburetors is not as advanced, and the failure rate is higher than the global industry average.

Therefore, Lin Yuanwu spent this period of time thoroughly studying carburetor repair.

He even paid out of his own pocket to buy a scrapped carburetor from a junkyard and kept disassembling it to study its internal structure.

Watching Lin Yuanwu's practiced movements, Fan Weimin couldn't help but whisper, "Brother Yuanwu, could you clean the old needle valve before using it again?"

Lin Yuanwu smiled, shook his head, picked up the old needle valve, and held it up to the sunlight: "No good, look at this sealing surface, it's already worn with a fine scratch."

"Cleaning it clean won't help; if it's not sealed properly, it will leak oil again when you put it back together."

"When repairing carburetors, the triangular needle valve is a consumable part, and we always keep it on hand in our shop."

"Replacing it when it's broken is easier and more reliable than repeatedly polishing it."

"After all, this is a car belonging to the Jianguo Hotel, so we have to make sure it doesn't break down after it's repaired."

"Otherwise, Shi Gui, your uncle will lose all face."

After saying this, Lin Yuanwu glanced at Li Shigui with a smile.

The latter responded with a simple, honest smile.

Soon, Lin Yuanwu took out a new needle valve and a small roll of fine sandpaper from the shop.

He put a drop of gasoline on the sandpaper and gently rubbed the valve seat.

"Before replacing the needle valve, the valve seat needs to be ground slightly."

"Use the finest wet sandpaper, add a drop of gasoline, and gently sand in circles until the valve seat surface is smooth and shiny. This will ensure a tight fit."

"Don't use too much force when grinding, and don't grind it off-center, otherwise you'll damage the valve seat."

"The entire carburetor cover needs to be replaced, which increases the cost."

"When installing, be gentle. Pinch the needle valve with your fingers and gently press it into the valve seat. Don't tilt the needle valve, or it will still leak oil."

After waiting for more than ten minutes, Lin Yuan armed the needle valve.

He then used his fingers to move the float, adjusting its height as he spoke.

"The height of this float determines the oil level. The float height of the BJ130's 231 carburetor is important; the standard is 18 millimeters."

"If you're not familiar with it at first, you can use a ruler to measure. If you're experienced, you can use your fingers to measure directly."

"It's about a finger's width apart. Remember that feel."

"The oil level is too high, causing the engine to consume more fuel and emit black smoke."

"The fuel level is too low, so there's no power and it's hard to start when the engine is cold."

After adjusting the float, Lin Yuanwu looked up at Jiang Hui and said, "Since you brought back solvent oil from Yanshan Petrochemical today, shall I give it a try?"

"Sure, let's see if the ones Yanshan Petrochemical bought are better than the ones we used before."

Jiang Hui, of course, had no objections.

Solvent oil is bought and used immediately.

It's most suitable for cleaning the internal parts of a carburetor.

Soon, with Fan Weimin's help, Lin Yuanwu poured the solvent oil into a small glass.

Then, insert a thin copper wire into the oil leveler's measuring hole and carefully clean the measuring hole and oil passages.

"The jet must be clear; it's the 'throat' of the carburetor. If it's blocked, the fuel supply will be uneven, and the engine will shake or stall."

"Look, this small round hole is the main jet, and the thinner one next to it is the idle jet. Both of them are easily clogged by oil and scale."

"When washing, gently insert a thin copper wire into the measuring hole and move it back and forth a few times, then dip it in some solvent oil and wipe it repeatedly."

"Try not to use hard iron wire, as it can easily enlarge the metering orifice. If the metering orifice size changes, the carburetor will be ruined."

After patiently and meticulously cleaning for more than ten minutes, Lin Yuanwu picked up a manual air compressor.

Blow through each measuring hole and oil passage one by one.

"When blowing, press the pump gently, don't press too hard."

"After blowing, dip it in solvent oil and wipe the measuring hole to make sure there is no residual oil before it is considered clean."

"Also, the carburetor gasket, you see, it's this black rubber gasket."

"Be careful when disassembling it, don't break it. If the gasket is old or damaged, it will leak air or oil after you put it back, and you'll have to replace it with a new one."

"We have spare parts in our shop, so you should familiarize yourselves with the spare parts situation in the future."

When Lin Yuanwu said this, he specifically glanced at Li Shigui.

The latter immediately nodded repeatedly.

Then Lin Yuanwu checked the sealing gasket on the carburetor cover to make sure it was intact before carefully putting the cover back on.

"When you close the lid, make sure it's aligned with the clips. Don't misalign it, otherwise it won't be secure and will leak oil."

"After fastening, gently shake the top cover with your hand to make sure it's not loose, then you can install the base screws."

After all the parts were installed, Lin Yuanwu carefully placed the carburetor back onto the engine mounting bracket.

Align with the screw holes, first screw in the four copper screws one by one, tightening them gently, then tighten them one by one in a diagonal order.

"When installing screws, tighten them in a diagonal order, not clockwise one by one."

"Otherwise, the carburetor base will be under uneven stress and easily deform. After it is reinstalled, it will leak air and affect the idle speed."

"After tightening, shake the carburetor by hand to make sure it's not loose, then you can connect the fuel line and power cord."

Although his legs are not very mobile, it does not affect Lin Yuanwu's ability to repair cars at all.

He connected the oil pipe, tightened the clamp, and then plugged the distributor wire back in, pressing it firmly to make sure it was secure.

Then I picked up the flathead screwdriver, aimed it at the idle screw, and gently turned it two turns.

"The idle speed screw is the lowest engine speed. It needs to be adjusted to be stable, even, and without vibration. You can tell by the sound."

"The standard idle speed of the BJ130 is around 800 revolutions per minute. We don't have a tachometer, so we just listen to the sound."

"If the sound is steady, without sudden changes in pitch, and the engine doesn't vibrate, then it's properly tuned."

"When adjusting, turn it little by little, don't turn it too much at once, otherwise the idle speed will be too high and it will waste fuel."

"The idle speed is too low, making it easy to stall."

With everything in place, Lin Yuanwu checked the oil pipes and wires again to make sure they were not loose or leaking.

He picked up the crank handle, ready to start the vehicle.

Tap the screen to use advanced tools Tip: You can use left and right keyboard keys to browse between chapters.

You'll Also Like