That evening, Lin Yuan returned to his dormitory at almost ten o'clock.
Matt, as usual, sprawled on the sofa playing video games, gunfire flashing on the TV screen. On the coffee table sat a half-eaten pizza and two empty Coke cans. Seeing Lin Yuan enter, he took off his headphones.
"You're back? How was your day?"
"I made a practice one." Lin Yuan put his backpack on the chair and sat down on the sofa. "I've never made a hand-and-a-half sword before, so I'll go through the process with a finished steel piece first to familiarize myself with the structure."
"Are you done?"
"It's finished. I tried making a few cuts, and it feels pretty good."
Matt gestured with his chin toward the pizza box on the coffee table. "I saved it for you. It's cold, just microwave it."
Lin Yuan put the pizza in the microwave and microwaved it twice. He then carried the heated pizza back to the living room, where he ate it while chatting briefly with Matt.
Matt asked how the practice sword blank he made today was going, and Lin Yuan said that the structure and heat treatment had been verified, and he would start making the official competition entry tomorrow.
Matt then asked what kind of craftsmanship was used, and Lin Yuan thought for a moment before simply saying, "It's not quite the same as a dagger."
The microwave pizza wasn't as good as his cooking, but it was enough to fill my stomach.
After finishing his meal, he threw the paper plate into the trash can, told Matt that he still needed to prepare the plan for tomorrow, and then went back to his room.
He closed the door, opened his laptop on the desk, and first looked up the materials Professor Robert had given him.
Today, while making practice sword blanks in the workshop, he personally experienced the geometric structure and heat treatment rhythm of the half-sword. Now, looking back at the professor's materials, he found corresponding data and theoretical explanations for many things he felt during the day's actual operation.
The thickness transition problem is the most obvious one.
When he was making practice sword blanks, he repeatedly adjusted the feed speed in front of the power hammer, because the thickness change of a hand-and-half sword from the root to the tip is not as easily summarized as one or two arcs as that of a dagger.
The sword blade is long, and the narrowing curve extends far. If the thickness of the middle section is not evenly transitioned, the distribution of the inertial torque during a chop will be off.
When he tried cutting the timber during the day, the feel was correct, indicating that the thickness transition was not a problem. However, he could feel that there was still a slight room for adjustment in the middle-forward section when applying force.
Looking at the geometric parameter table in the professor's materials now, the data does indeed indicate the theoretical tolerance range for the thickness transition in the middle section.
He then turned to the chapter about the longsword being quenched and deformed.
During the day, the practice sword blanks were made using oil quenching. The 1084 high-carbon steel was used for oil quenching, which was standard practice and the result was very stable—the sword blanks were straight after quenching, without warping or cracks.
But the sword to be made tomorrow will be forged together with blessed silver and steel billets.
Silver has a different thermal conductivity than steel. During quenching, the cooling rate of the silver-containing area will differ from that of the pure steel area, resulting in a more complex thermal stress distribution than that of ordinary steel billets.
He turned to a new page in his notebook, wrote a few lines about the key points of quenching, then crossed them out and rewrote them.
Before quenching tomorrow, we need to pre-determine the distribution area of silver on the sword blank. During normalizing, we cannot just follow the standard temperature of the steel blank. We need to treat the cooling of the silver-containing area and the non-silver-containing area differently.
He wrote down several process parameters next to him and then made modifications based on the parameters in the professor's materials.
After closing the professor's file, he opened his browser and looked up information about the hand-and-half sword.
I'm not looking at the technical specifications—the professor's information on the technical specifications is already detailed enough.
What he wanted to know were the things not written in textbooks: what problems did swordsmiths who had made half-swords most often encounter in practical tests, and what details would be noticed by opponents or judges?
After browsing for more than half an hour, he came across an old post discussing the center of gravity of a longsword. It mentioned that the center of gravity of a half-sword directly affects the grip, but the grip is also affected by the thickness of the hilt and the texture of the leather. It is not enough to just look at the center of gravity data; you have to look at how the hilt fits.
Another person added that the center of gravity of the one-and-a-half-hand sword he made before was standard, but the leather covering of the hilt was made of the wrong material, and the leather became slippery after a few cuts during testing.
He wrote down the grip feel and the choice of foreskin in his notebook.
He originally planned to use vegetable-tanned leather to cover the handle, referencing the common practice for European hand and half swords. However, upon further reflection, he realized that traditional Chinese sword handles are made of stingray leather—after polishing, the grain is even and fine, and the natural anti-slip texture is an effect that no embossed leather can replicate.
Moreover, stingray skin dries faster than vegetable-tanned leather and doesn't feel slippery when it gets sweaty.
His father had a high-end custom-made sword made in Longquan, and the hilt and scabbard were both made of this material. Since the sword itself is a fusion of Eastern and Western forging techniques, it makes sense that the hilt is made of stingray skin.
The remaining scraps can be used to make a stingray skin scabbard—depending on whether there's enough time on the last day.
He noted down two surface treatments in his notebook: stingray skin and beeswax. After thinking for a moment, he added two more words next to it: scabbard.
After extracting all the information he found online, he closed his notebook.
Next up were the blueprints for the Paladin's Cross Sword. He unfolded the system panel, and the blueprints were laid out before him.
The crafting process for the Paladin's Cross Sword and the Cloud Pattern Steel Blade are based on completely different logics.
The cloud-patterned steel relies on the repeated folding of two types of steel, soft and hard, to form patterns on the interface between the layers—this is how the flowing cloud pattern on the dagger comes about.
The Paladin's Cross Sword does not require forging.
Its core is to incorporate blessed holy silver into the sword blank, and the holy silver is integrated with the steel blank during the forging process.
Today, while making the practice sword blank, I verified the basic geometric structure of the hand-and-a-half sword. Tomorrow, I will add the requirements of the Paladin's Cross Sword blueprint to this foundation. The general process is as follows: using 1084 high-carbon steel as the base, when building the initial structure, I will sandwich the blessed holy silver into the middle layer of the steel blank, and then forge it, allowing the silver material to gradually integrate into the steel blank under high temperature and hammering.
But where the holy silver came from was a question.
His first reaction was to use the experimental pure silver stored in Professor Robert's workshop as a substitute—the blueprints clearly stated that ordinary silver could be used instead, but the additional special properties would be greatly weakened.
The few pieces of pure silver in the lower drawer of the professor's materials cabinet were of high purity and the right size, making them the most practical solution to replace the blessed silver.
I'm already ready to write this plan into my notebook.
Then he stopped writing.
Regular silver can be used as a substitute, but how big is the difference between the substitute and the original?
He flipped back to the blueprints and saw the material requirements section. After the description of Blessed Holy Silver, there was a line of small print: "Special silver material that is offered and blessed before the altar. When forged into a steel billet, it can activate divine properties."
Ordinary silver retains only its basic divine affinity.
Fantasy materials—these four words circled in his mind.
Since cloud-patterned steel and stacked forging are both provided by the system, will the system shop have such items?
He opened the materials section of the system shop and began scrolling down page by page. Adamantite, Mithril, Boiling Star Stone, Dragonscale Iron... When he finally reached the category of Sacred Materials, Blessed Sacred Silver was prominently listed.
The label is consistent with the drawing, and the price is ten gold coins.
Lin Yuan subconsciously glanced at the gold coins he had accumulated over nearly two years in the system's storage compartment.
More than two hundred of them had been lying quietly in the corner. I never knew what they were for before. I only took one out to sell for money when I was a freshman. The rest had been left here. I never expected that they would be used for shopping in the system.
Ten gold coins can be exchanged for a piece of silver that can activate divine attributes; it's not cheap.
But he had already spent eleven years honing his forging skills, and another two years combining university theory with his family's traditional craft.
If you settle for ordinary silver for this sword, the special attributes on the blueprint will forever remain just words on the blueprint.
He clicked "buy". The number of gold coins jumped from over two hundred to just over two hundred. A small piece of silver appeared in his storage compartment.
He took the silver ingot from the storage compartment and placed it on the desk. The silver ingot wasn't large, just enough to forge a sword.
The surface has a very faint sheen, visible even without a light source. It's not the shine of polished silver, but a softer luster, like diluted moonlight.
He flipped the silver ingot over.
The feel is not significantly different from ordinary silver—cool, smooth, and with a certain weight.
But when you hold it in your hand, you feel that this silver is warmer than it looks. It's not a very obvious temperature difference; it's more like a subjective illusion caused by the skin coming into contact with a certain material.
He weighed the silver ingot in his palm before putting it back into his system storage.
Just as he was about to close the shop interface, his gaze swept over another category in the materials section—leather and fabric.
A thought struck him, and he clicked in to browse.
The system store's material categories were much more detailed than he had imagined; there were dozens of types listed under the leather category alone.
He flipped through the pages in order and soon found the stingray skin.
The label reads: Deep-sea stingray skin, with even and fine scales, tough and wear-resistant texture, specially tanned, waterproof and sweatproof.
Price: One gold coin for ten cards.
Lin Yuan placed the order almost without hesitation.
One gold coin and ten processed stingray skins—one piece of leather was more than enough for him to make a sword hilt cover and a scabbard, with a few left over for later use.
The number of gold coins jumped again, and a neatly stacked pile of leather appeared in the system's storage compartment.
He took out a sheet and flipped through it—the scales were plump and tightly arranged but not stiff, and you could feel the fine and even friction when you touched them with your fingers.
It's even better than the ones his father used in Longquan.
The hilt is made of this leather, so it won't slip when held, whether it's dry or wet.
He put the stingray skin back into his storage compartment and closed the system shop.
The process requirements on the drawings are very clear: the silver material must be sandwiched into the steel billet early in the forging process and go through the entire forging process together with the steel billet.
If silver is added only after the steel billet has been forged halfway, the bonding surface between the silver and steel will not be sufficient, affecting the final sword properties and effects.
In other words, the first step in forging tomorrow will be to put the holy silver in, and throughout the forging process in the morning, the silver will be inside the steel billet, enduring high temperatures and hammering.
This requires precise temperature control for each heating cycle.
Silver has a much lower melting point than steel—pure silver melts at about 960 degrees Celsius, while 1084 is forged at temperatures above 1,000 degrees Celsius.
If the silver has already melted inside the steel billet when it is heated to the forging temperature, the liquid silver will be squeezed out along the forging surface under hammering, which will not only result in material loss, but also leave voids inside the steel billet.
A balance must be found between the forging temperature and the melting point of silver.
He calculated several sets of data in his notebook and, referring to his experience in controlling the furnace temperature when practicing sword blanks during the day, set himself a forging temperature limit that was lower than usual but still within the operable range.
Go through tomorrow's process. Go to the workshop in the morning.
The material used is 1084 high-carbon steel, the same material used for the practice sword blank.
When building the initial structure, the silver is directly sandwiched into the middle layer—no forging is required. The silver material is simply placed flat between two steel plates, fixed with a spot welding machine, and then heated and forged.
The first round of forging is the most crucial. Before the silver melts, the steel billet and the silver layer must be hammered together to achieve a preliminary bond, so that the silver transforms from an independent interlayer into a microscopic distribution embedded in the steel billet matrix.
Afterward, the silver material gradually integrates into the steel billet with each heating and hammering. In the final product, the silver is not a single layer, but a tiny silver phase evenly distributed throughout the entire blade material.
Normalizing must be performed before quenching.
The normalizing temperature of silver-containing steel billets needs to be set separately and cannot be directly copied from the parameters of practice sword billets.
The quenching method still adopts the process of pre-cooling, local quenching of the blade, and then immersion in oil, just like the practice sword blank. However, the angle and speed of immersion in oil need to be adjusted according to the distribution of the silver-containing area.
The quenching parameters of the practice sword blank can be used as a reference standard, and adjustments can be made to them for the use of holy silver.
Coarse grinding and pickling are done on the third day.
After fine polishing, the full effect should be achieved.
The hilt is made of ebony core covered with stingray skin, and the scabbard is made of the same material.
He glanced at the note he had written in his notebook, "stingray skin and beeswax," and crossed out the beeswax—the stingray skin itself was non-slip and didn't need to be soaked in beeswax.
He reviewed the steps and process parameters listed in his notebook for tomorrow, making sure nothing was missing, then closed the notebook and turned off the computer.
In the lower right corner of the system panel, Blessed Holy Silver and a stack of stingray skins lay quietly in the storage compartment.
Let's start with this piece of silver tomorrow.
He turned off the room light, lay on the bed facing the ceiling with his eyes closed, went over the things he needed to do tomorrow in his mind again, and then turned over and went to sleep.
You'll Also Like
-
The dragon just wants to stay at home, but the players are frantically upgrading their technology.
Chapter 310 2 hours ago -
Nuclear Sword Immortal Starting from Type-Moon
Chapter 220 2 hours ago -
CS: Reincarnated Girl, Can You Become Stronger by Earning Rice?
Chapter 365 2 hours ago -
One Piece: Who still has dreams?
Chapter 151 2 hours ago -
Tokyo Wrestler
Chapter 234 2 hours ago -
Douluo Continent: The Peerless Hunting Heavenly Lord, Huo Yuhao!
Chapter 182 2 hours ago -
The only player in the world of Bleach.
Chapter 338 2 hours ago -
The sweeping eunuch in the library gets stronger by signing in.
Chapter 151 2 hours ago -
I'm the villainous Dragon King? I start with a free 100-pull gacha pull for the female lead!
Chapter 159 2 hours ago -
A fat man who was reborn from the dead? He transforms into a perfect male god in a week.
Chapter 751 2 hours ago